Carrera 10110 Operations Instructions download pdf (Page 4)

Preparation of start

Before ﬁrst being used, the WIRELESS+ speed controller should be

fully charged. Place the speed controller in the charging cradle and

switch on power to the track. While the unit is charging, the LED

on the speed controller will ﬂash. When charging is completed, the

LED

will light up continuously.

When using a lithium polymer rechargeable battery, it is possible to

top up the speed controller at any time.

Binding process

SET

CHANNEL

SET

CHANNEL

SET

CHANNEL

Before the speed controller can be used to control the cars, it must

be “bound” to the receiver.

To do this, switch on the control unit.

The receiver indicates it is ready for operation by a revolving light

signal in the segment display

Push the “SET” button

once until the ﬁgure 1 appears in the seg-

ment display

. The number shown is then the address of the car.

Switch to the next address by further pressing the button.

Now press the binding button

on the top of the speed controller.

The speed controller signals a successful binding process with

ﬂashing of the LED, while the receiver indicates it by revolving lights

in the segments. The binding process is now complete and the

speed controller is ready for use.

To bind the second speed controller, follow the same procedure.

Press the “SET” button

on the receiver twice, until the ﬁgure

2 appears

. Then press the binding button

on the second

speed controller.

When the binding process has been successfully carried out, the

cars can be coded to the corresponding speed controller. For coding

the cars, setting the speed, braking behaviour and tank capacity also

see the owner’s instructions for the Black Box, Control Unit or car.

To display the address set for the speed controller, press once on

the binding button

on the top of the speed controller.

The LED

will then ﬂash, according to the address set.

If the speed controller is not actuated, it switches automatically after

about 20 seconds into energy-saving mode. The speed controller

can be reactivated by pressing the tappet or the lane-change button.

Troubleshooting

In case of any malfunctions, please check the following:

• Is the adapter unit correctly installed facing the direction of travel?

• Is the speed controller battery properly connected?

• Is the battery fully charged?

• Does the LED on the controller ﬂash while charging?

• Is the speed controller bound to the receiver?

• Has the speed controller got a duplicate address assignment?

Note:

During operation small car parts as spoilers or mirrors may get oﬀ or

brake due to being original detailed parts of the car model. To avoid

this it is possible to remove them before operation.

All Carrera spare parts are available in the webshop:

carrera-toys.com

Delivery exclusively to Germany, Austria, Netherlands, Belgium and

Luxembourg.

Maintenance and care

To ensure a proper operation of the motor-racing circuit, all race-

track components should be regularly cleaned. Pull the plug prior

to cleaning.

Racetrack: Keep the track surface and track slots clean with a

dry cloth. Do not use any solvents or chemicals for cleaning. When

it is not in use, store the racetrack in a clean and dust-protected

location, preferably in the original cardboard box.

Technical specifications

Output voltage: Toy transformer

18 V

54 VA (Carrera DIGITAL 124)

14,8 V 51,8 VA (Carrera DIGITAL 132)

lithium polymer rechargeable battery: 3,7 150mAh

Electricity modes:

1.) Operating mode = cars are operated via speed controllers

2.) Idle mode = speed controllers not activated, no game

3.) Stand-by mode = after approx. 20 minutes idle mode the

connecting section switches to stand-by mode. LED ﬂashes at

long intervals. CURRENT CONSUMPTION < 1 watt / 1w

By operating the speed controller the stand-by mode is ﬁnished,

the racetrack returns to idle-mode again.

4.) Oﬀ-state = power supply unit disconnected from mains supply

This device is marked by “selective sort throught” symbol related to

sort through domestic, electric and electronic, waste. This means

the product must be treated by a specialized “sorting/collecting” sys-

tem in accordance with European directive 2002/96/CE, to reduce

the impact upon environment. For more precise information, please

contact your local administration. Electronical product which are

not going through special collecting, are potentially dangerous for

environment and human health, because of dangerous substance.

Output voltage: Toy transformer

14,8 V

51,8 VA

lithium polymer rechargeable battery: 3,7 150mAh

Electricity modes:

1.) Operating mode = cars are operated via speed controllers

2.) Idle mode = speed controllers not activated, no game

3.) Stand-by mode = after approx. 20 minutes idle mode the

connecting section switches to stand-by mode. LED ﬂashes at

long intervals. CURRENT CONSUMPTION < 1 watt / 1w

By operating the speed controller the stand-by mode is ﬁnished,

the racetrack returns to idle-mode again.

4.) Oﬀ-state = power supply unit disconnected from mains supply

Requirement for FCC Part 15

Warning: Changes or modiﬁcations not expressly approved

by the party responsible for compliance could void the user’s

authority to operate the equipment.

Note: This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instruc-

tions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in

a particular installation.

If this equipment does cause harmful interference to radio or televi-

sion reception, which can be determined by turning the equipment

oﬀ and on, the user is encouraged to try to correct the interference

by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver,

• Connect the equipment into an outlet on a circuit diﬀerent

from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for

help.

Warnings

Guidelines and warnings about using the LiPo battery/

batteries:

LiPo rechargeable batteries are much more sensitive than the

traditional alkaline or NiMh rechargeables. For this reason all in-

structions and warnings must be scrupulously observed. Incorrect

treatment of LiPo rechargeable batteries may cause a ﬁre. In han-

dling, charging and using the LiPo battery/batteries supplied, you

take over all responsibility for the risks attached to lithium batteries.

• Non-rechargeable batteries must not be recharged!

For recharging batteries, only the charging cradle supplied may be

used. If this instruction is disregarded, there is a risk of ﬁre which

may endanger your health and/or cause damage to property.

NEVER use any other charging unit!

• Rechargeable batteries may only be recharged under adult super-

vision. When charging, never leave the battery unattended.

When you recharge the battery, you should always be in the vicinity

to keep watch on the process so that you can react to any possible

problem.

• If the battery swells or deforms during either discharge or charging

process, stop the process immediately. Remove the battery as fast

and as carefully as possible and place it on a safe and open area

away from any ﬂammable materials, and keep it under observation

for at least 15 minutes. If you continue to charge or discharge a bat-

tery which has already started to swell or deform, there is danger of

ﬁre! Even at the slightest sign of swelling or deforming, the battery

must be taken out of service.

• The battery supplied must be charged in a safe place away from

ﬂammable materials.

• Store the battery at room temperature (16 - 18 °C) in a dry place.

Do not expose the battery to direct sunlight or any other sources of

heat. Temperatures over 50 °C are generally to be avoided.

• Always recharge the battery after use to avoid the possibility of its

becoming deep discharged. When it is not in use, recharge the bat-

tery from time to time, say every 2-3 months. Failure to observe the

methods of handling described above may lead to defects.

• When changing batteries do not use any sharp or pointed objects

or tools. Avoid damaging the protective foil around the battery at

all costs.

• When replacing defective batteries, only the recommended battery

types may be used. Damaged or unusable batteries are hazardous

waste, and must be disposed of accordingly.

• Never throw batteries, rechargeable or otherwise, on the ﬁre or

expose them to high temperatures. This may cause a ﬁre or an

explosion.

• The electrolyte and electrolyte vapour in the LiPo batteries are

hazardous to health. Always avoid direct contact with electrolyte.

If electrolyte makes contact with skin, eyes or other parts of the

body, it must immediately be washed out or oﬀ with plenty of fresh

water and a doctor must be consulted.

• Rechargeable batteries are not toys and must not fall into the

hands of children. Keep batteries inaccessible to children.

• The connector clips / battery connections must never be short-

circuited!

• The toy is only to be operated with a transformer or power pack

designed for use with toys!

• The transformer / the power pack is not a toy!

1 2 3 4 5

7.80.12.43.00 · 01/2013 5

Comments to this Manuals

No comments

Carrera 10110 Operations Instructions Page 4

Comments to this Manuals

Related products and manuals for Toy parts Carrera 10110